Thursday, July 26, 2012

Changing the oil on a BMW R1150GS.

I'm not the most mechanically minded person on earth, so if you need to follow this guide you're probably fucked.

To change the oil on a BMW R1150 GS you will need.

  1. A BMW 1150GS
  2. Oil, about three and a half litres worth.
  3. A new oil filter
  4. A 10mm socket and drive thing for socket.
  5. A bigish allen key. I dunno what size.
  6. An oil filter wrench. The filter is all up in the engine, you need this badboy to get it out and get the new one in.
RIMG0135
Take your GS and put it on its centre stand on flat ground. If its not absolutely fucking pishing down outside take it for a wee spin first to warm it up. Warm oil drains better than cold oil.
Put some old newspaper down in case you make a cunt of things and spill oil all over the floor resulting in you slipping later and dropping your bike.

RIMG0137
Loosen the four nuts that hold the sump guard on. These fuckers can get pretty badly seized so put some copper grease or something on them. If the rubber mounts break use mole grips or plumbers pliers to unscrew the bastards. 

RIMG0138
You should now have the sump guard off and four nuts. Two longish ones from the front with big washers and two smaller ones with wee washers from the rear.

RIMG0142
Remove the sump plug to drain the oil out into an appropriate receptical, this will take a few minutes so go and have a beer or a cup of tea or something. I spoke to occasional Mikeworld visitor Paul and his dog Dot for a few minutes.


RIMG0139



RIMG0141
Once all the oil has finished draining replace the sump plug. Put a new crush washer on it if some spare ones came with your oil filter, the spare crush washers are for you gearbox and final drive plugs. DO NOT OVER TIGHTEN YOUR SUMP PLUG. Remove the old oil filter. Mind, this will be full of oil that with pish out all over the shop so be careful. Make sure the rubber ring from the old filter comes out too. Use some oil to lube the ring on the new filter and use the oil filter wrench to install it. Just don't tighten it up too much. Again, more ballet dancer than sumo wrestler.

RIMG0143
Pour your new oil in. I went for this semi synthetic 20w50 from www.opieoils.co.uk. Put three and a half litres in then start your bike. It might knock it's cunt in for the first few seconds before the new filter fills up and the oil gets around the engine. Turn the bike off. Once you're sure there's no leaks replace the sump guard remembering to grease the threads so you don't get seized nuts. Check the oil level glass. If its half full perfect, if not top it up a wee bit. Mind that from top to bottom the sight glass is about a quarter of  a litre so don't go mental.

RIMG0135
You should now be back to a scene like this but with oil all over the place. You're bike will appreciate it though.

Perfect.

17 comments:

  1. Too funny. Made me laugh. I'm wondering how difficult a job you had based on all the cursing. Hehe

    ReplyDelete
  2. Is all the bad language really necessary to change oil? Also, your procedure is flawed. Always pre-fill the new filter with oil prior to installation. You might be better off just riding rather than offering maintenance suggestions.

    ReplyDelete
    Replies
    1. I find the bad language helps. You're right about filling the filter with oil, but thats a bit beyond my skillz.

      Delete
    2. Fuck this, fuck that and fuck that cunt.

      Delete
  3. Brilliant. You always make me chuckle.

    And some days, I do think cursing is needed to change the oil. Most definitely.

    ReplyDelete
  4. I was pissin myself reading this, you sure do have a way with words mike.

    ReplyDelete
  5. I too thought I was fucked when that cunt of mine had crash bars to decuntify that fucker. I bitch fucked that cuntbag whore till the fucker slather fuck cunt slut. Then I damn fuck cock sucker clit faced whore. It's just that easy. Thanks for the pictures too.

    ReplyDelete
  6. Remind me never to go adventure riding with you...between us tow half wits we would make a dim wit! Cool read.

    ReplyDelete
  7. I can see signs of shoddy maintenance Mike ! Tell faithir tae get that floor painted :o)

    ReplyDelete
  8. Real world mechanicking. Swear words are part of the toolkit. A good vocabulary is essential!

    ReplyDelete
  9. This was so helpfull and so was the the language cheers to you mate and thanks 4 the added pics fucking brill

    ReplyDelete
  10. This comment has been removed by a blog administrator.

    ReplyDelete
  11. Positive site, where did u come up with the information on this posting? I'm pleased I discovered it though, ill be checking back soon to find out what additional posts you include. sight glasses

    ReplyDelete
    Replies
    1. Thanks. I thought it was pretty fucking positive myself. I came up with the info by changing the oil on the bike myself.
      I done a fucking good job eh?

      Delete
  12. I was reading the thread and immediatly thought this guy is scottish ! cos he talks just like me , scrolled up and saw it was Mike .made my day

    ReplyDelete
  13. Straight to the point, i love it. Dont let anyone stop us bloggers. 먹튀검증

    ReplyDelete